![]() I will try mine in the RSGB Autumn Series Data on Wednesday so good luck setting yours up and a big thanks to the others for the help, it has answered a question for me as well. It does seem a very complicated setup for something that is setup on my FT920 so simply but I guess that's technology for you. I had to go into mmtty settings TX and enable PTT/Fsk more than once but once things were done in the right order everything works fine. I've re-loaded working setup config from SD card. Everything in FT8 mode seems to work fine except there is no power output in TX mode. Yet another video in my Field Day 2020 series. Make sure the Hardware tab is selected (this is the tab the Configurer starts up in by default. Fully dove-tailed with N1MM+, calling the digital window on N1MM+ invokes FLDigi and FLRig (if needed). After these preliminaries, start N1MM Logger+ and open the Configurer ( Config > Configure Ports, Audio, Mode Control, Other ). Flrig 1.4.4 (rig control) Fldigi 4.1.20 (for other digital modes) WSJT-X 2.2.2. For more detailed information, check out the sections on Downloading and Installing MMTTY, 2Tone and fldigi in the manual. I use mmtty and Logger32 in a separate folder with EXTfsk for general logging but couldn't understand why EXTfsk was not being found in N1MM, I had put a separate mmtty in the N1MM folder but then realised that I was looking in the wrong place and hadn't put EXTfsk in the N1MM folder so that runs nicely now. I mention N1MM because it does change IC-7300 setting, at least in digital modes. I am not sure if you can set the port sharing app to start automatically but that's for a later date. FT8 & CW/Cwget are set as they were and all is hunky dory. Make sure you also Check to enable on the lower screen there to see the ENABLED file name phrase appear. Then choose the ADIF logfile in FLDIGI’s directory. Under ADIF Functions section, enable ADIF monitor of FLDIGI’s ADIF log. Followed the instructions and mine is now working beautifully on fsk rtty. Run LOG4OM and from its settings menu: Make sure cat interface is Omnirig. step by step instructions would be best if you can provide them.Hi Pete, I set my 7300 back to default after saving configuration to sd card and renaming. I still need some help, if anyone can provide it. The side effect is that fldigi instance 'hangs' in the background when N1MM switches to another mode (e.g. Unfortunately I was not able to follow those instructions successfully. Unfortunately, when used by N1MM, the waterfall-only mode has no menu to set this option, and the default is unfortunately set to 'ask' which is nonsense, because both the launch and the shutdown are controlled by N1MM. Setting up of N1MM will involve telling it the path to Fldigi.' Just use N1MM, set-up Fldigi as your preferred digital engine, and then select Field Day in N1MM Logger and off you go. 'use Fldigi "engine" within N1MM as opposed to plain Fldigi. Let's see what else is new When I got the IC-7300, it was a real thrill to operate RTTY (FSK). We now have two virtual COM ports on the IC-7610. ![]() Probably something simple that I am missing, but right now i am stumped. 41 Icom 7610 N1MM One Cable RTTY FSK CW How To by K0PIR Published DecemUpdated The Icom 7610 N1MM configuration is simple and similar to the IC-7300. Plug your microphone directly into the mic input on the sound card, plug your headset directly into the speaker output. Select ‘1 zero or single card’ in the top list, then ‘default’ in the first ‘select device’ list. ![]() Can anyone tell me how to get my FLdigi logger to send it files to the N1MM logger? Start N1MM logger and go into the ‘Configurer / Audio’ tab. For PSK31 and other non-WSJT digital modes, you can use MMVARI or fldigi as the digital engine, with no special setup required.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |